Видео

It doesn't matter, any adapter with a USB-C output would do the trick. 😊

@@onlinemarketer4510 тук въобще не съм се старал да запазя монетата, понеже не е скъпа 😊 Използвам настройки по дефолт. Laser 50W JPT source Working area 200 mm Line distance 0.031 mm Speed 1300 Power 30% Frequency 30 kHz Вече не помня, но тук може да съм се заиграл с мощността. Аз бих започнал от ниска и после бих увеличил постоянно. Другият вариант е с по малка сила и повече повторения, за да не навредя монетата.

@@pick_pick_pick I'm so glad you like it 🤩

Thank you! I'm glad you like it. I haven't taken measurements for accuracy, but I guess it measures accurately enough. Such a difference of 2000mA is quite large. What brand is your phone?

@@DjaniAgain i think im doing wrong way! Had to buy dummy usb loader then fully charge battery then discharge and measured mah. But thanks for reply 😃

@@wassimhajji6725 I sold it when S24 Ultra came out, and yes, it was in great shape and all in working condition! Great device. Now I'm testing the same with S24 Ultra, so far S pen making me problems

@@DjaniAgain great to hear this, i made 5 days ago 3 minutes videos on salt water with my S23ULTRA, after rinsing and drying it, it works normally now, I wouldn't do this madness again since i was worried little bit, but it seems that samsung are stong enough

No, I didn't had that type of an issue. The two yellow big things are the capacitors, and they can be measured. The simplest is to hook a multimeter on them to measure voltage, if there is any. They are for few seconds of energy supply, if power cuts of suddenly. This way dashcam will have enough time to save the clip. When powered, even without capacitors the device should work. Test with different power supply and another cable. How often does it reboot, or it is bootlooping constantly?

@@DjaniAgain It reboots like every 1-2 minutes I’d say. It doesn’t appear to be heat related since it happens indoors with a cold camera too.

Have you tried to turn it on without a memory card? Maybe it's causing the issue 🤔 Also, try to reset the dashcam, may help. One more suggestion try to update dashcams firmware.

I know exactly what you're talking about. I'm sorry that you have a problem too. Apparently, heat or vibration ruined them 😢

Everything is on the tiny crystal dot. Unfortunately I can't zoom-in this much 😊 I hope you liked this little experiment!

@@DjaniAgain they put everything in the tiny crystal!? Damn okay... XD Yes, the Experiment was nice :D

@@FixitEasyDIY Thank you my friend! I had to deal with this problem for a year atleast, said enough is enogh 😅

You have to wait a bit much my friend, with these prices 😅 I hope you liked the video

It's a standart tower type desktop fiber laser, 50W and with JPT laser source. I'm saying standart, because form factor doesn't matter much on these laser. Most important parameters are the max power output and the laser source itself. I hope this helps, if you have any questions don't hesitate to ask 😊

Не се притеснявай, похвално е че си честен. Дали е хейт или не, гледам коментарите да ги приемам като градивни с цел да задобрявам в това, което правя. А и казаното от теб си е истина. Всеки по-голям канал не може да си позволи смесване на контента. Желая ти успех с канала! ✌️

Правя видеа свързани с моето всекидневие, както съм го описал в информационната секция. Затова днес снимам Васко жабата а утре някаква техника. За съжаление не съм си специализирал канала в нещо. Благодаря за отзива!

If done properly maybe not, but this is a regular everyday coin in exchange, and did it just for entertainment 😊

@@DjaniAgain ok

✌️

I will test it with S24 Ultra today and will tellbyou the result. But you can see in the comments, that I reached up to 83W of power output using this cable. So I'm pretty sure that it will support Superfast 2.0 charging

@@DjaniAgain thanks . I've ordered this cable .

@@ahmednaeem5002 As promised, my friend. Now I'm charging my phone via this cable. The phone shows message Super fast charger 2.0 connected and it draws only 14W of power 😅 which is Samsung's fault. The phone is S24 Ultra and current charge is at 66 percent

@@DjaniAgain samsung fault 🫠. What's the solution bro. I'm only buying this cable to charge my s23 ultra

@@DjaniAgain can you please try this cable with a proper 45w adapter and charge s23 ultra and see if it's doing superfast charging 2.0 and also plz check the 0 to 100 charge time.

I don't think engraved glass can be cleared my friend. Maybe with polishing 🤔, But it won't be easy.

Usually I swear that the people paint black the glass and after the engraving they wash that. Why don't you paint it ?

@@panos9624 not necessary for CO2 lasers, seem to handle the glass pretty well

Thanks! It sounds good 😊

​@panos9624 people paint the glass when using a 420nm diode laser. A co2 laser uses a different wavelength. 10,600nm I believe. Different wavelengths for different lasers each react with different materials in different ways. As far as I'm aware, a co2 laser is the only type that can engrave on transparent materials without needing to cover it with something first

It's called Fiber laser!

It's bulgarian coin my friend! ✌️ Greetings from Bulgaria 🇧🇬

I'm glad you liked it! ✌️

It served me 2 full years, after that i sold it for a second life with another owner! I'm pretty sure the phone is doing fine. The buying side was a company, which checks the phones and if OK, they being sold with another 2 year warranty. The fact they didn't find any damage during their testing, makes me confident for it's condition. Samsung, Number 1 ✌️

Nice idea! ✌️

If I'm not wrong, this was mentioned in the user manual. Something like holding the button while plugging the device to the power source. PS: watch from 0:43, Question 3

@@DjaniAgain I will try plugging it in with the correct 5v source and test it. Thanks

😂😅🤣

This is called fiber laser

Thank you! 😁

@@DjaniAgain i think on the same scale you has of bad choices you have of intelligence...

@elbirdway9074 I appreciate your opinion!

Looks better in any range or better at all?

@DjaniAgain I don't see much of a difference in terms of detail and megapixels. I've had my s22u for about a year almost and I just don't feel the need to upgrade at the moment

@@jerrodmays83 My S22 Ultra was a great device, great camera hardware. Decision fo upgrade came from the SoC itself, Exynos was very battery hungry. I had battery anxiety all the time. And at the same time, vaichki were talking about s23 and snapdragon chip, how much better it was. No regrets about the upgrade. 😁

There is a clear detail difference

S24 demolishes

😅😂🤣

Свети, свети 😁

I can't say much about the notebook, covers are from colored synthetic leather, in this clip it's yellow covered with black coat. I don't know what the black paint is, but it fells off easily with alcohol. The settings for the laser are generic, nothing special. Lens 150 mm Power 30% Line distance 0.031 mm Cross hatch On, or just repeat twice Speed 1300 mm/s Frequency 30kHz

😅🤣😂 Watch second part my friend, then both sides ofbthe wallet will be 👌

Coin you mean

@@DjaniAgain Unless you link it here, I'm never finding that.

Just did it! Thanks for the suggestion my friend ✌️

You too? I didn't mention anything about it, because I thought only I had not heard of such batteries 😅

✌️

I don't know my friend, maybe at times, but latter is superior if you ask me. I'm happy with the upgrade. Don't get me wrong, S22 Ultra is still a Beast machine. It served me for 2 years with no problems, though I tortured it not once or twice 😅

Um where the stabilization on the s24 absolutely killed it and much more details and natural vibe

😅😅😅

Do Kaiweets have one? I haven't seen anything like it on their website.🤔

I'm glad you liked it Brother! ❤️

I have to admit that I used it only for an hour. In this hour, the soldering iron was great no complaints at all.

This is because of Android 14 restrictions! Follow developer's guide, here: github.com/tribalfs/GalaxyMaxHzPub/releases

Sorry to hear that my friend! But why they are claimed 4-30V then 🤔 I only have up to 100W chargers and cables, so can test this meter in this range. Thanks for sharing this useful info ✌️

Dunno mate. Don't think it's the voltage as much as the protocol itself. The tester died completely a few minutes after my first post, got a refund.@@DjaniAgain

Can we say that this adapter is safe up to 20V? I'm sorry for the difficulties you've been through. At least they gave you your money back!

I used it without issues @ 24V / 5A (120W). However as I said I think it's safe to use up to 30V without any problems, imo it's the new PD3.1 protocol compatibility that is the culprit here. Ordered a new one, I liked it a lot, just wish it had a quicker response time, it's so slow. Other than that it's an awesome little tool.@@DjaniAgain

Do you recommend purchasing? Haven't fixed PD 3.1 yet? ​@@the_game

Mine is from there too. I've put other models in the description, too. ✌️

You welcome! I hope this helped you with the choice ✌️

Thank you my friend! And I totally agree with you! 👌

I like it very much, it's not big, but it gives a lot of useful information. I'm in love with it 😍